Narwhal 1/8in M35 Cobalt Drill Bits 13-Pack 135° Split Point Review 2026: Is it Worth It?
Quick Analysis Verdict
"Great for metalworkers and DIYers who need short, hard-metal drilling bits for stainless, cast iron and hardened steel; not for deep wood drilling or tasks needing long-reach bits."
Review Methodology
Why this analysis may help before you buy
Rating signal
We weigh star rating together with 1,149 visible reviews so a rating is not judged in isolation.
Buyer momentum
Recent purchase activity and category badges help us identify products shoppers are actively considering.
RefreshBuy score
The score combines performance, quality, value, and ease-of-use signals for this category.
Decision Guide
Is Narwhal 1/8in M35 Cobalt Drill Bits 13-Pack 135° Split Point a good fit for you?
For shoppers comparing Power & Hand Tools products, this Narwhal option looks strongest on value with a 9.0/10 signal. The main area to double-check is quality, especially if that is your top priority.
Rapid, precise small-diameter holes in hard metals (stainless, hardened steel, cast iron) where short, rigid bits and split-point starts are desirable.
strong review coverage, 4.4/5 rating, and 50+ recent monthly purchases.
Value score 9.0/10 at $13.99 current tracked price.
Choose it if
You want a Power & Hand Tools pick where the strongest measurable signal is value and the current review base is large enough to compare with alternatives.
Compare alternatives if
Your buying decision depends mostly on quality, long-term durability, or a lower final checkout price after marketplace changes.
Before buying
Check both Amazon Canada and Amazon US from this detail page, then compare similar Power & Hand Tools products below before deciding.
Rapid, precise small-diameter holes in hard metals (stainless, hardened steel, cast iron) where short, rigid bits and split-point starts are desirable.
Great Value
Moderate to high for thin-plate and sheet-metal work when used with cutting oil and conservative speed/pressure; limited by short length and overheating if abused.
Key Buying Points
M35 Cobalt alloy (contains ~5% cobalt) gives elevated red-hardness versus HSS so bits cut and retain edge when drilling stainless and hardened steels.
Fully ground flute and precision 1/8" diameter deliver consistent hole size and straighter holes in thin-sheet and plate work — users report prolonged edge life when used with light oil.
135° split point tip minimizes walking and starts quickly on metal without a pilot hole, speeding repeated hole patterns in thin stainless and steel panels.
Short total length (2.55") with 1-3/8" flute keeps bits rigid for hand drills and drill presses, reducing runout and chatter on small-diameter holes.
Uncoated finish means faster cutting at moderate speeds with cutting oil but increased sensitivity to overheating under heavy feed; bits are resharpenable.
Included tough plastic case organizes 13 bits securely for toolbox storage and prevents shank damage or lost pieces on the jobsite.
Strong value proposition — multiple users note cost-effectiveness versus branded cobalt sets while delivering comparable life for routine metal drilling.
The Catch
Very short flute/overall length limits use to shallow holes and prevents reach into recessed or deep work; several buyers found them too short for many jobs.
Uncoated cobalt heats faster under heavy load; without proper coolant or reduced speed the bits dull quicker or risk premature breakage.
Not optimized for wood or masonry — geometry and short length make them poor choices outside metalworking.
Quality variance reported by a minority — a few users noted initial dullness or inconsistent edge feel out of the box.
Small diameter increases break risk if aggressive feed or excessive side-loading is applied; require proper speed/pressure control.
Performance Scorecard
Common Questions & Expert Insights
Q: Will these drill bits cut stainless steel reliably? ▼
Q: Are these bits long enough for through-hole drilling in thick material? ▼
Q: Do these fit standard drill chucks and drill presses? ▼
Q: Will a cordless drill handle these bits in stainless? ▼
Q: Can these bits be resharpened when dull? ▼
Q: Do they require cutting oil or coolant? ▼
Q: How do these compare to titanium-coated HSS bits for metalwork? ▼
Q: Are these better than carbide bits for small holes in steel? ▼
Q: How should I maintain these bits to maximize lifespan? ▼
Q: If a bit dulls, is it safe to keep using it until it breaks? ▼
You May Also Like
Top-rated alternatives in Power & Hand Tools